DESIGN OF A MULTI-COMMODITY HOLDER FOR MOTORBIKES
The paper deals with the design and fabrication mulit- commodity holding device. Using the concept of morphology, the product is extracted from the need of a common person in Indian scenario. There is a consistent need of a multipurpose carrying device which helps a common person who uses a two-wheeler for daily transportation specially a motor bike for holding objects like LPG cylinder and other common objects. The method used to for achieving the target is done using the general model of design given by Shigley. For which a CAD software is used to model the concept. Then the stability and feasibility of the design is checked by the FEMbased solver for known boundary conditions. The same model has been then fabricated using the general manufacturing techniques like Sheet metal and welding process. The model has been tested on road using a filled LPG cylinder. It has been observed that the existing model perform well within the given boundary conditions. Further changes may be required if the model of the motor bike changes.Index Terms: Multi-commodity carrier, FEM, CAD, Sheet model.
"Design And Finite Element Analysis Of Domestic Lpg Cylinder Using Ansys Workbench" Cvr Journal Of Science And Technology, Volume 14, June 2018,Issn 2277 – 3916.
"Experimental Analysis Of Magnetorheological Dampers When Subjected To Impact And Shock Loading" Communications In Nonlinear Science And Numerical Simulation 13 (2008) 1978–1985,1007-5704/$ - See Front Matter 2007 Elsevier B.V. All Rights Reserved.Doi:10.1016/J.Cnsns.2007.03.028
"Fatigue Behaviour Analysis Of Mechanical Components Subject To Random Bimodal Stress Process: Frequency Domain Approach" International Journal Of Fatigue 27 (2005) 335–345,0142-1123/$ - See Front Matter Q 2004 Elsevier Ltd. Doi:10.1016/J.Ijfatigue.2004.09.004.
"Similarity Assessment Of 3d Mechanical Components For Design Reuse" Robotics And Computer-Integrated Manufacturing 22 (2006) 332–341, 0736-5845/$ - See Front Matter R 2005 Elsevier Ltd. Doi:10.1016/J.Rcim.2005.07.005.
"The System For Sheet Metal Forming Design Of Complex Parts" Journal Of Materials Processing Technology 157–158 (2004) 502–507,0924-0136/$ – See Front Matter © 2004 Elsevier B.V, Doi:10.1016/J.Jmatprotec.2004.07.110.
"Finite Element Modeling Of Sheet Fonning Process With Bending Effects", Journal Ofmaterials Processing Teclmology 63 (1997) 733-737, 0924-0136/97/$15.00 © 1997 Elsevier Science Sa, Pii S0924-0136(96)02715-X.
"Reliability Analysis Of Mechanical Components And Systems "Nuclear Engineering And Design 19 (1972) 259-290, North-Holland Publishing Company.
"Solder Joint Reliability Prediction Of Flip Chip Packages Under Shock Loading Environment" AsmeInterpack’ 05 July 17-25, San Francisco, California, Usa, Proceedings Of Ipack2005.
"Optimal Placement Of Fixture Clamps: Maintaining Form Closure And Independent Regions Of Form Closure" 676 Õ Vol. 124, AUGUST 2002, Transactions Of The ASME.
"Dynamic Response of a Clamped Circular Sandwich Plate Subject to Shock Loading" SEPTEMBER 2004, Vol. 71 Õ 637, Journal of Applied Mechanics, 2004 by ASME.
"Expert System Approach in Design of Mechanical Components" Engineering with Computers 4, 185-195 (1988) The State University of New Jersey, New Brunswick, NJ 08855, USA.
"Stress in V-section band clamps" Proc. Instn Mech. Engrs Vol. 218 Part C: J. Mechanical Engineering Science C17903 # IMechE 2004.
"Theory of Curved, Clamped, Piezoelectric Film, Air-Borne Transducers"ieee transactions on ultrasonics, ferroelectrics, and frequency control, vol. 47, no. 6, november 2000.
"Study on LpgCylidner Parent Metal Mechanicalproperties" International Journal Of Advanced Engineering Technology, International Journal Of Advanced Engineering Technology E-ISSN 0976-3945.
"Analysis Of Bending Effects In Sheet For-Ming Operations" International Journal For Numerical Methods In Engineering”, VOL. 25, 253-267 (1988) 0029-598 1/88/010253-15$07.50.
- There are currently no refbacks.